chipping machine中文是什么意思

• 砍枝机
• 刨丝机
• 削片机

• "chipping"中文翻译    adj. (雀，栗鼠等)唧唧叫的。
• "machine"中文翻译    n. 1.机(器)，机械；机关，机构。 2.印刷机器；缝 ...
• "electric chipping machine" 中文翻译 :    电榔头
• "plastic chipping machine" 中文翻译 :    平面式裁断机; 塑胶切碎机; 塑料切碎机
• "pneumatic chipping machine" 中文翻译 :    气榔头
• "chipping" 中文翻译 :    n. 〔pl.〕(削、凿下的)碎屑，碎片，薄片；【机械工程】切屑。 adj. (雀，栗鼠等)唧唧叫的。
• "back chipping" 中文翻译 :    背缝焊渣铲除; 背缝凿净,背缝凿平; 背面凿平（熔接）; 背面錾平; 背琢; 铲根; 铲焊根; 清根
• "chipping allowance" 中文翻译 :    切削余量
• "chipping bed" 中文翻译 :    铲凿清理台
• "chipping campden" 中文翻译 :    平坎普登; 奇平卡姆登
• "chipping carpet" 中文翻译 :    石屑毯层
• "chipping chisel" 中文翻译 :    铲凿; 平头铲刀; 平头凿; 平錾; 凿刀
• "chipping concrete" 中文翻译 :    碎石集料混凝土
• "chipping edger" 中文翻译 :    双削齐边锯
• "chipping goggles" 中文翻译 :    铲削用护目镜; 敲锈眼镜
• "chipping hammer" 中文翻译 :    尖头榔头; 空鹤镐头; 敲锈锤气动锤铲边枪; 敲渣锤; 碎石锤; 修整锤; 凿锤; 錾锤; 錾平锤
• "chipping heading" 中文翻译 :    制材削片联合机
• "chipping knife" 中文翻译 :    剥铅刀
• "chipping maching" 中文翻译 :    削片机
• "chipping mark" 中文翻译 :    表面铲伤
• "chipping norton" 中文翻译 :    奇平诺顿; 契平诺顿
• "chipping of propellant" 中文翻译 :    固体燃料的碎裂
• "chipping ongar" 中文翻译 :    奇平昂加
• "chipping out" 中文翻译 :    清炉壁
• "chipping qualities" 中文翻译 :    切片质量

• Plastic chipping machine
  塑胶切碎机
• It includes more function modules , which work under control of 80c51 single chip machine
  该分析仪包括多个功能模块电路，它们都是在80c51单片机控制下进行工作的。
• This project uses the single chip machine mcs - 51 as its fundamental controlling unit and adopts many digital chips . scrambling is fulfilled by compressing some of the synchronous tips carried by rf signal
  本方案以单片机mcs - 51作为加解扰系统的核心控制器件，通过将有线电视射频信号的某些行同步头压缩掉的方式实现对电视信号的加扰。
• After the precise measure liquor conductivity under certain temperature , the temperature compensation of conductivity is studied in this paper . the method of temperature compensation with single chip machine is studied emphasizedly . the method include polyfiting formula and consulting scheme
  在解决准确测量某温度下溶液电导率基础上，本文还对电导率的温度补偿作了总结和研究，重点研究了运用单片微机进行温度补偿的方法，包括拟和经验公式和查表。
• So in one hand it requires the wafer ' s diameter to be more large in order to enhance the productivity , and on the other hand it puts forward more strict requirement about the crystal perfection and electricity character . especially the electronic character and the equality of micro - area in the crystal wafer has become the key factor to determine whether the device can be made on it or not . so the resistivity measurement of micro - area become one most important procedure in the chip machining . to ensure the produce quality of chip and the perfect performance of final production , the four - probe testing technology need to be deeply studied
  图形日益微细化，电路尺寸不断缩小，目前ic制造以8英寸、 0 . 13 m为主，预计在2007年左右将以12英寸、 65nm为主，这一方面要求圆片直径不断增大以提高生产率，另一方面对晶体的完美性、机械及电特性也提出了更为严格的要求。特别是微区的电学特性及其均匀性已经成为决定将来器件性能优劣的关键因素。因此，微区电阻率的测试成为芯片加工之中的重要工序。
• The thesis was detailed to analyze the interference source , interference path of every kind of interference and the classification of the interferences that single - chip machine system may appears , putting forward every kind of method of the hardware anti - interference ; then takes the research and approach to every kind of method of the software anti - interference
  论文详细分析了单片机控制系统可能出现的各种干扰的干扰源、干扰途径以及干扰的分类，提出了硬件抗干扰的各种方法；然后又对软件抗干扰的各种方法进行了研究和探讨；最后以一个系统非正常复位的故障恢复设计的例子论述了单片机系统故障诊断的思路和方法。

• chipping machine 意味
• chipping machine перевод
• chipping machineとは意味chipping machine チッパー[化学]